Painted aluminium scrap price is the wrong thing to worry about most of the time. On US boards in 2026, painted extrusion runs roughly 8 to 14 percent below clean. A New Jersey yard posted bare 6063 at about $1.30/lb with painted at about $1.20/lb in April. A Texas recycler listed bare at about $1.10 and painted at $0.95 to $1.00 in January. That's a modest discount, not a slashed rate, and Australian yards work the same logic with their own numbers.
Here's why. Paint and powder coat burn off cheaply in the furnace, and the alloy underneath is identical. The buyer isn't paying to remove the coating. The discount is about certainty and what's still attached to the metal, not the paint itself.
Some buyers also treat lightly painted material as its own middle grade between clean and contaminated, so the gap isn't fixed. It varies yard to yard. If the yard down the road pays the same for painted and clean, that's plausible. Grading is local. Ask before you assume a discount.
What actually costs you money on a painted load
The coating is usually the smallest deduction on the ticket. The real price-killers are what's still bolted, glued or stuck to the aluminium:

- Steel screws and brackets
- Hinges
- Plastic thermal breaks and trims
- Rubber gaskets and seals
- Glass
- Mixed alloys in the load
Each one matters for a different reason. Steel is a different metal the furnace rejects, so it has to be pulled before melting. Plastic and rubber burn dirty. Glass contaminates the melt. Mixed alloys can't be graded as one lot at all, so the buyer either sorts it or downgrades the whole load.
The trap is spending hours sanding or stripping paint when the deductions come from what's still attached. Say you've got a pallet of painted window extrusion with steel screws and plastic inserts. The hour that pays is the one spent pulling screws and plastic, not the one spent with a sander.
And what about big loads? Doesn't stripping pay then? Only if the buyer confirms a premium that beats your labour. Ask first, and get it in writing before you commit the hours.
When painted pays more than clean
Here's the case that breaks the rule. Painted siding and gutters, cleaned, ran about $0.73 to $0.89/lb on US yard boards in October 2026. That beat some clean bare sheet, which sat at roughly $0.65 to $0.98/lb across July to October, while painted or old sheet ran $0.59 to $0.75/lb. The reason: siding is a narrow alloy range in large volumes, so the buyer knows exactly what they're getting, and the paint burns off in remelting anyway.
So 'painted always pays less' is not a reliable rule. Alloy consistency and attachments matter more than the coating. The question to ask about any painted lot is what alloy it is and what's attached, not whether it has colour on it.
Anodised aluminium is not painted
Anodising is a thin oxide layer grown from the aluminium itself, not a coating applied on top. It burns off the same way in the furnace. Most yards, including most US yards grading 6063, put anodised material in with painted or bare extrusion. So no, anodised is not the same as painted, but it usually lands in the same price bracket. Don't assume a separate or worse rate until you've asked.
How to describe a painted lot so you get paid right
Describe what the material is, not a grade you can't verify. 'Painted window extrusion with plastic inserts and steel screws' beats 'clean 6063' every time, because it's true and it lets the buyer grade it on the facts.

The mislabelling trap is real. ScrapTrade's reference grade for 6063 is clean, uncoated window and door extrusion. Call a painted, screwed-together window frame 'clean 6063 extrusion' and the load gets regraded on arrival at the contaminated rate. Worse, it burns trust with the buyer, and that costs you on the next deal too.
'But how do I know I'm getting the painted rate and not the contaminated rate?' You can't be sure until the buyer has seen the material. That's exactly why photos, honest descriptions and written requirements matter. Photograph the lot overall and close up, disclose the coating and every attachment, and if you can't identify the alloy, use a plain description like mixed aluminium scrap and ask buyers what testing they need.
On the screws: remove them where it's safe and practical, but ask the buyer what preparation they actually want before spending the time. And never dismantle anything pressurised, electrical or hazardous to get there.
Should you strip the paint
At an 8 to 14 percent gap on extrusion, stripping rarely pays back at Australian volumes. Weigh your labour against the gap and the answer usually comes up no.
The condition that changes it: a buyer who specifically wants clean uncoated 6063 and will pay for it. If that's on the table, get the requirement and the price in writing before you do the work or book a truck. Powder coat is thicker than wet paint but the same logic applies. Ask the buyer how they grade it rather than guessing.
Your next step before the truck leaves
Run the checklist:

- Photograph the lot from a couple of angles, plus close-ups of fittings and coatings
- Disclose the coating and every attachment, including mixed or coated pieces
- Ask the buyer their grading policy for painted material
- Get any premium requirement in writing before accepting the deal
Use the ScrapTrade calculator as an indicative reference only. The binding number is the buyer's written offer after they've seen the material. List your scrap on ScrapTrade and get offers from verified buyers across Australia.
FAQs
Does painted aluminium scrap for less than clean?
Yes, painted material prices below clean uncoated metal at most buyers, because the coating is contamination they have to deal with. How big the gap is depends on the buyer, the alloy and how much paint is on the load.
Should I strip paint off aluminium before scrapping?
Usually no. On a typical load the price difference rarely covers the hours of stripping, and burning paint off is a false economy: the fumes are hazardous and the heat can damage the metal. It only stacks up if you have serious volume and a buyer who confirms a clean-metal price in writing.
Is anodised aluminium the same as painted?
No. Anodising is a finish grown into the metal surface, not a layer sitting on top, so many buyers treat it more favourably than painted stock. It's still not clean uncoated metal though, so call it anodised rather than claiming clean 6063 extrusion.
Do I need to remove screws from aluminium window frames before selling?
Not necessarily. Steel screws, hinges and rubber seals affect how a buyer classifies the load, and some want attachments out while others take them and adjust the price. Pull them only if it's quick and safe, and never dismantle anything pressurised or electrical to get at them.
How much less do you get for painted aluminium window frames?
There's no set percentage. The discount depends on the buyer, the amount of paint and hardware on the frames, and the volume, so the same load can price differently at different yards. Describe the frames accurately with photos, then compare quotes instead of trusting one number.
Why does painted cladding pay more than clean sheet?
Consistency, mostly. Painted cladding is usually one recognisable form at a known gauge, while a 'clean sheet' lot is often mixed offcuts with rivets or sealant still in it. Buyers price what they can't verify on the low side, so a tidy single-form load can beat a mixed one even with the paint on it.

